Awning ELBOWS Schedule-40| CSC Textiles USA/Canada

AWNING PARTS Below Are Sized for Schedule-40 Piping (As explained below)

Aluminum ~ Slip-Fit ELBOWS

6S / 5S Elbow:

Sized for
Schedule-40-Pipe
> READ Below <

4S-Littco
4-S Elbow
w/ 2-Set-Screws

Alum 5-S SLIPFIT ELBOW w/4Set-Screws
90 degree SLIPFIT elbow with stainless steel
securing screws. Gusseted for extra strength.
For Piping 1.050" OD (over 1"OD )
#Elb-5SL AL (3/4"-ID-Sched40) (USA Only)

Alum 6-S SLIPFIT ELBOW w/4Set-Screws
90 degree SLIPFIT elbow with stainless steel
securing screws. Gusseted for extra strength.
For Piping 1.315" OD (over 1-1/4"OD )
#Elb-6SL AL (1"-ID-Sched40) (USA Only)

6-S ELBOW

MFR DISCONTINUED
$39.95 for TWO Littco

Alum 4-S SLIPFIT ELBOW w/2Set-Screws
90 degree SLIPFIT elbow with stainless steel
securing screws. Gusseted for extra strength.
For Piping 0.840" OD (over 3/4"OD )
#Elb-4SL/AL-2427 (1/2"-ID-Sched40)

[ Prev ] < Awning FITTINGS > [ Next ]

IMPORTANT: AWNING FITTINGS Are Sized Based On Awning-Pipe's INSIDE-DIAMETER
(Not The Outside-Diameter)... See The Noted ID And OD figures provided for each fitting,
And Compare To The ACTUAL MEASUREMENTS On The Pipe Which You Are Using...
If not sure, using the actual OD Pipe measure compared to the OD figure above, may be wiser.

RAIL & Welt > [ TRACK And WELT ]

IMPORTANT: READ Before Ordering
The measurements for these fittings are based on the pipe sizes of Schedule 40 Pipe,
which is measured by the inside diameter of the pipe, not the outside as with marine fittings.

FOR EXAMPLE:
1/4"ID Schedule 40 pipe has an outside diameter of 0.540 (OD) inches (over 1/2"OD )
1/2"ID Schedule 40 pipe has an outside diameter of 0.840 (OD) inches (over 3/4"OD )
3/4"ID Schedule 40 pipe has an outside diameter of 1.05 (OD) inches (over 1"OD )
1"ID Schedule 40 pipe has an outside diameter of 1.315 (OD) inches (over 1-1/4"OD )
OD = Outside Pipe Diameter; ID = Inside Pipe Diameter

[ A *MINIMUM $30 Order in Product Required + S/H costs, On ALL Fittings ordered. ]

*Note: Select Carefully, since All Sales Are Final...

The aluminum hardware is cast alloys that are best suited to each applications.
All parts have a smooth surface with a bright finish.
Set screws, hinge screws, bolts and nuts are of stainless steel unless otherwise indicated.
Many of the parts appear similar to their counterparts in the boat top trade, they tend to be
larger castings and in many cases are not as well finished as the equivalent boat parts.

OD = Outside Pipe Diameter; ID = Inside Pipe Diameter

~ Awning Fittings Only ~
Sizing NOTE: If You Are Using Other Types of Piping, use that Tubing's Outside-Diameter (OD),
and Compare to the Awning-Fitting's OD Info above, that it would accommodate...

CSC ~ SUPPLY GROUP

CSC ~ Founded by Veterans.