EYE-END Cap SLIPFIT Schedule-40 | CSC (610) 767-7555

: Use Your Credit-Card Or PayPal Securely :
SELECT Item below . . . Then ADD-To-Cart
~ First-Quality Professional-Grade: Awning Hardware ~ ALUMINUM ~ Awning FITTINGS SLIP-FIT EYE END Caps, Rafter TEE, AWNING Aluminum Fittings - Hardware Parts, Schedule 40 Fittings

USE: Application in the construction of Awnings

OD = Outside Pipe Diameter; ID = Inside Pipe Diameter : READ Below . . .

Aluminum SLIP-FIT EYE END for 0.540"OD Tubing Littco
for Schedule-40-Pipe 1/4"ID (with 0.540"OD / Outside Diameter)
Application in the construction of awnings.
For Piping 0.540" OD (over 1/2"OD ) #j2361 6pc-pack

HD slip-fit eye end fasteners with stainless steel lock-screws.

Littco

Many Manufacturer-Discontinued Items : Call or eMail For Available Stock-Check

Aluminum SLIP-FIT EYE END for 0.840"OD Tubing j2420 FOUR
for Schedule-40-Pipe 1/2"ID (with 0.840"OD / Outside Diameter)
Application in the construction of awnings.
For Piping 0.840" OD (over 3/4"OD ) #j2420 4pc-pack

HD slip-fit eye end fasteners with stainless lock-screws.

Aluminum SLIP-FIT EYE END for 0.840"OD Tubing j2420 SIX/L-4-S
for Schedule-40-Pipe 1/2"ID (with 0.840"OD / Outside Diameter)

Application in the construction of awnings.
For Piping 0.840" OD (over 3/4"OD ) #j2420 6pc-pack

CALL For Stock Check

SIX-pc

MFR DISCONTINUED

Littco

Alum SLIP-FIT EYE END HD for 1.050"OD Tubing j2364/L-305
for Schedule-40-Pipe 3/4"ID (with 1.050"OD / Outside Diameter)
Heavy Duty SLIPFIT eye end fasteners with stainless steel
lock-screws. Littco

For Piping 1.050" OD (over 1"OD ) #j2364 HD

Littco

w/2-Set-Screws

Alum SLIP-FIT EYE END Super-Duty for 1.315"OD Tubes j2366/L-315
for Schedule-40-Pipe 1"ID (with 1.315"OD / Outside Diameter) Littco

Heavy Duty slip-fit eye end fasteners with stainless steel lock-screws.
For Piping 1.315" OD (over 1-1/4"OD ) Littco #315 SD

BACK To CSC INDEX

IMPORTANT Read Carefully: AWNING FITTINGS Are Sized Based On Schedule-40-Pipe's INSIDE-DIAMETER
(With A Larger Outside-Diameter)... See The Noted ID And OD figures provided for each fitting,
And Compare To The ACTUAL MEASUREMENTS On The Pipe Which You Are Using...
If not sure, using the actual OD measure of the Pipe, compared to the OD figure below, may be wiser.

FITTINGS for Awnings
The aluminum hardware is cast alloys that are best suited to each applications.
All parts have a smooth surface with a bright finish.
Set screws, hinge screws, bolts and nuts are of stainless steel unless otherwise indicated.
Many of the parts appear similar to their counterparts in the boat top trade, they tend to be
larger castings and in many cases are not as well finished as the equivalent boat parts.

IMPORTANT: READ Before Ordering
The measurements for these fittings are based on the pipe sizes of Schedule 40 Pipe,
which is measured by the inside diameter of the pipe, not the outside as with marine fittings.
FOR EXAMPLE:
1/4"ID Schedule 40 pipe has an outside diameter of 0.540 (OD) inches (over 1/2"OD ),
1/2"ID Schedule 40 pipe has an outside diameter of 0.840 (OD) inches (over 3/4"OD ).
3/4"ID Schedule 40 pipe has an outside diameter of 1.05 (OD) inches (over 1"OD ),
1"ID Schedule 40 pipe has an outside diameter of 1.315 (OD) inches (over 1-1/4"OD ).
OD = Outside Pipe Diameter; ID = Inside Pipe Diameter

EXAMPLE 2: If Your Schedule-40 AWNING Piping has an Inside-Diameter (ID) of 3/4",
and a Outside-Diameter (OD) of just over One-Inch, Then You would Use the 3/4" Fittings...
If not sure, Call or E-mail me...

~ RAIL & Welt > [ TRACK And WELT ]

*Please NOTE: The Actual Colors May Vary From Those Viewed On The Screen...
Different Computers and Settings, Monitors, Flat-Screens, Lap Tops, and Processors May Depict
Colors Differently, as I'm sure most of you have concluded...
Our Listings are for those familiar with these product lines and the colors...
So Please Be Sure you know what you are ordering, since All Sales Are Final...
Thanks, Dave :o)

~ A CS Corp Company ~

CSC ~ SUPPLY GROUP