Osborne Standard-GROMMET Dies, Tools, Pads

: Use Your Credit-Card Or PayPal Securely :
SELECT Item below . . . Then ADD-To-Cart
Professional Workroom Tools ~ TOOLS & DIES For Grommets ~ Osborne Grommet Hand Setting Dies and Tools, Osborne Grommet Dies & Spur Grommet Dies, Hole Cutting Pad below...

Grommet Pro TOOLS, DIES, & CUTTERS

GROMMET SIZING CHART:      Size-Number = HOLE-Diameter
SIZE #00=3/16"Hole-Diameter    #0=1/4"Hole    #1=9/32"Hole
#2=3/8"Hole<<Most Popular    #3=7/16"Hole    #4=1/2"Hole    #5=5/8"Hole
Available By Phone:   #6=3/4"Hole    #7=29/32"Hole    #8=13/16"Hole
Osborne-series (Standard sizing) ~ Cruiser-series (Euro/Metric sizing)
[ Prev ] < PRO TOOLS >  [ Next ]   ~ Scroll Down ~

Osborne PLAIN GROMMET Hand Setting DIES
Each set consists of two parts, the punch and the die.
Note that the spur and the plain dies are Not interchangeable, you must have the specified die for each type and Grommet Size. Never strike a cutter or die with a metal hammer. Always use a Rubber or Composite mallet for hole punching or setting grommets or fasteners. A steel hammer strike such a severe blow that the metal in the dies absorb the entire shock and begin to crystallize. This crystallization begins to weaken the dies, which will become brittle and fail prematurely.
#J-For Osborne PLAIN-Grommet Hand-Setting Dies

$79. Each

#5020 Sz#00 PLAIN DIE Osborne

$79. Each

#5034 Sz#0 PLAIN DIE Osborne

$99. Each

#5021 Sz#1 PLAIN DIE Osborne

$99. Each

#5022 Sz#2 PLAIN DIE Osborne

$125. Each

#5023 Sz#3 PLAIN DIE Osborne

$125. Each

#5025 Sz#4 PLAIN DIE Osborne

$139. Each

#5026 Sz#5 PLAIN DIE Osborne

For OSBORNE-type
PLAIN GROMMETS

HOLE-CUTTERS

GROMMETS

NOT FOR
Osborne-SPUR
Grommets
See Other DIES
(Below)

NOT FOR
CRUISER-Type
Grommets
See Other DIES
HERE

Select "ADD To CART"... Type QUANTITY & Update

Osborne SPUR-GROMMET Hand Setting DIES
Each set consists of two parts, the punch and the die. Grommet setting tools for the Osborne Spur grommets. These require special dies as setting teeth on the spur washer uses a slightly different size and die face from the plain and must ensure the spur teeth fit into the rolled rim for maximum strength. Note that the spur and the plain dies are not interchangeable, you must have the specified die for each type. Never strike a cutter or die with a metal hammer. Always use a Rubber or Composite mallet for hole-punching or setting grommets or fasteners. A steel hammer strike such a severe blow that the metal in the dies absorbs the entire shock and begins to crystallize. This crystallization begins to weaken the dies, which will become brittle and fail prematurely.
#J-For Osborne SPUR Hand-Setting DIES

$99. Each

#5019 Sz#0 SPUR DIE Osborne

$99. Each

#5055 Sz#1 SPUR DIE Osborne

$110. Each

#5028 Sz#2 SPUR DIE Osborne

$119. Each

#5027 Sz#3 SPUR DIE Osborne

$125. Each

#5029 Sz#4 SPUR DIE Osborne

NOT FOR
Osborne-PLAIN
Grommets
See Other DIES
(Above)

For OSBORNE-type
"SPUR" GROMMETS

NOT FOR
CRUISER-Type
Grommets
See Other DIES
HERE

Select "ADD To CART"... Type QUANTITY & Update

HOLE-CUTTING PAD (Hole-Cutter Sold Separately)
For maximum life of your cutters and die setting equipment, always use a rubber mallet and not a steel hammer to set fasteners, grommets or to hole punch. Use this pad under the material you are punching. The special surface absorbs the impact and allows the cutter to cut the material, not the bench underneath. Cutters stay sharper and last longer.
#J-6120 Cutting-PAD only

$69. Each

#J-6120 PAD Only ~ EACH: Approx. 10" x 10" x 3/8"Thick

HOLE-CUTTING
PAD Only

(Does NOT Include
Hole-Cutter Shown)

HOLE-CUTTERS

[ Prev ] < PRO TOOLS > [ Next ]

SHIPS DOMESTICALLY In USA -or- In Canada (No Border-Crossing Required)

CSC ~ Founded by Veterans.